1. Cherry-picker
   Rake
2. Snake
   Vulture

Have you ever heard of someone "snaking" a drain? They're extending a jointed metal hose down a clogged drain. The metal spiral on the end of the hose will either push the clog through to a wider part of the drain, or grab onto the clog and pull it out when the snake is retracted.

1. A ball-and-cock mechanism
   A U-bend
2. A push broom
   A wet vac

A "wet vac" sucks up standing water, allowing you to empty the tank outside, where it's safe. It's a handy thing to have in case of emergencies.

1. An appliance repair
   An electrical repair
2. A painting job
   A plumbing repair

Generally speaking, electricity is the most dangerous thing a handyman can work with, causing potentially fatal shock or the outbreak of fires. Bear in mind, too, that the risk can be to other people after the repair is finished, so sometimes it's important to say, "You should call an electrician for this."

1. Sure!
2. No!

This is a difficult job that's best tackled by a specialist. Among other things, you'll need to have a place to take the septic sludge once it's out of the tank, one that meets federal and state safety regulations.

1. Making screw holes larger
   Hanging the hammer up within easy reach
2. Pulling out nails by the head
   Prying boards apart

The claw is shaped like a very narrow V, and hooks around the shaft of the nail, just under the nailhead. Then, using the hammer like a lever, you can pull the nail out. This doesn't work as well when a conscientious carpenter has sunk the nailhead below the surface of the wood for aesthetic reasons.

1. Drill
   Entrenching tool
2. Phillips screwdriver
   Vise

A vise is a kind of tabletop clamp, operated by a screw. Most often, you'll attach it to your workbench, and use it for holding small object in place while working on them with both hands.

1. Laminate flooring
   Pipe cleaners
2. Sandpaper
   Handymen! Persistence is essential.

Sandpaper, commonly used for smoothing wood, is rated by grit. The higher the number, the finer the "grit." You'll often start with a low number and move higher as you're close to finishing a woodworking project.

1. Clamp
   Glue
2. Pipe
   Wood

Clamps are very useful in handyman work. Often, they'll hold two objects together while the adhesive between them dries, for example.

1. In the attic
   In the refrigerator
2. Under the sink
   Under the stairs

The P-trap is found right under your sink's drain, whether it's a kitchen sink, bathroom, or elsewhere. The reversal in pipe direction traps a small amount of water, which keeps unpleasant sewer gases from rising up into the home.

1. A band saw
   A flat screwdriver
2. Needle-nosed pliers
   A stripper

A wire stripper is especially made to do this job, removing coating without scratching or kinking the wire. Be careful, though: Bare wires, obviously, can relay electric current.

1. A drill press
   A press gang
2. A Sealyham drill
   A table auger

A drill press requires less effort to be guided by the worker. It also tends to have a more powerful motor than those found in handheld drills.

1. 2 hours
   6 hours
2. 24 hours
   One week

While silicone caulk (the most common kind) can feel dry to the touch as quickly as within 1 hour, it needs 24 hours to fully cure. This might vary depending on the humidity where you live.

1. Needle-nosed pliers
   Kitchen shears
2. Bolt cutter
   Miter saw

Kitchen shears are sometimes called "poultry shears" or "game shears," and they're used for cutting meat, especially at joints. They're a cook's tool, though handymen will probably enjoy them if they take a similarly craftsman-like approach to cooking.

1. Duct tape
   Electrical tape
2. Measuring tape
   Packing tape

Measuring tapes, like a tailor's "tape measure," aren't sticky. In this case, a "tape" is something that scrolls out, measures a length, and can be retracted. An electrician's "fish tape" works much the same way, except it is used to route wiring.

1. A lopper
   A hand spade
2. A rototiller
   A weed whacker

"Weed whacker" is the common term for a string trimmer (some people spell it "wacker.") But the real name is "string trimmer," and it really is a lowly string, powered at very high speed, which serves as the blade.

1. Jigsaw or scroll saw
   Hand saw
2. Miter saw
   Table saw

The term "jigsaw" is falling out of use, maybe because the name was co-opted by the puzzle, then by a series of horror movies. The more common term today is "scroll saw."

1. The house's siding, before painting
   The interior walls, before painting
2. A car or truck
   Pots and pans with stuck-on food

A pressure washer gets every last bit of dirt or grime off exterior walls, patio surfaces, driveways and gutters. It's not for indoor use.

1. A bathtub
   A door hinge
2. A bed frame
   Hardwood flooring

Caulk is a waterproof sealant, often used in bathrooms. It's usually dispensed with a "caulking gun," which isn't as violent as it sounds.

1. Carrying a supply of three-prong adapters in your toolbox
   Shutting off the water at the main
2. Labeling the circuits in the breaker box
   Rewiring the whole house in 220V

One key to making a safe electric repair is shutting off the electricity at the box. And that goes much faster if you label the circuits! That way, you're not going back and forth from the box to the site of the repair, checking and re-checking whether you've finally found the right switch.

1. For ease of going in and out of the room for supplies
   It's a great time to disassemble and oil them.
2. Paint on hinges makes them stiff.
   This step is unnecessary.

In general, getting paint on items like door hinges, outlet boxes and smoke alarms looks sloppy. In addition, when paint dries it acts as a light glue, preventing ease of motion or removal.

1. Anchor
   Bolthole
2. Drift
   Scabbard

This makes sense -- the plastic piece is holding the screw in place. Otherwise, the weight of the object being screwed in can easily cause malformation of the hole, over time, leading to a loose fit.

1. Construction adhesive
   Caulk
2. Mortar
   Fish tape

Construction adhesive is a many-purpose glue. One of its advantages is that it can be used inside or outside -- it isn't prone to breaking down when exposed to weather.

1. Hanging art
   Mounting a flat-screen TV
2. Mounting a bike rack
   It's "stud detector," not "joist detector."

Studs and joists are related things -- they're timbers in the frame of the house. But joists are horizontal while studs are vertical, so if you're doing any of the above tasks, you need a stud detector.

1. Garden shears
   Pinking shears
2. C-clamps
   Tin snips

These are also called "tinner's snips." They are usually made of carbon steel and should be used with great care.

1. Ceramic
   Linoleum
2. Stone
   Wood

Sandblasting is also known as "abrasive blasting." It's a harsh process that you wouldn't use on more delicate materials like linoleum.

1. Bolts
   C-clamps
2. Nails
   Screws

A nail gun makes quick work of carpentry projects. Do we need to remind you to be careful? Probably not.

1. A bolt emerges on the other side.
   A screw is easier to remove.
2. A bolt is usually made of harder material.
   These are terms for the same thing.

Screws and bolts are similar, but not the same. Both are threaded, but a screw is tapered and embeds in the material it's forced into, while a bolt is cylindrical, emerges from the other side and is fastened with a nut.

1. A hard hat
   A wedge
   An escape path
2. Gloves
   All of these

Tree removal is a potentially dangerous job. You want safety gear including a hard hat, goggles and gloves, and an escape path (in the opposite direction of the falling tree). The wedge is to hold the cut you're making open and thus keep the weight of the upper trunk from pressing down on the blade.

1. True
2. False

While this might seem like a good idea, pushing down can cause scratching. If you're not getting the effect you want, try changing out the sandpaper for a fresh piece first

1. A band saw
   A chain saw
2. A drill
   A workbench

Chain saws are commonly used to cut down trees. Hence the word "felling" - a "felling sight" is a visual guide to where to make a notch in the tree trunk, an early step in cutting down the whole tree.

1. Ergonomics
   Loss prevention
2. Pilates
   Physiomechanics

"Work injuries" in this case includes gradual and repetitive strain. Ergonomics covers the prevention of such injuries for both office workers and for manual laborers.

1. Drill press
   House
   Ladder
2. Electric screwdriver
   Either "house" or "ladder"

Handymen will often reach for an "A-frame" ladder to reach ceilings, high points on a wall, et cetera. It's possible that they're also working in an A-frame house, as well -- that's a home with a high, center-pointed roof.

1. There's a backup somewhere in the outflow pipes.
   There's not enough water in the tank.
2. There's not enough water pressure in the supply system.
   A clog is imminent.

The slowdown in the pipes might not mean a clog, but water is not flowing efficiently. You'll see a sign of this in a "bounce": the water level goes down, then rebounds before the flush is complete.

1. Plain water
   Olive oil
2. Simmering milk
   Simmering vinegar

Plain water will break up some of the dried paint. However, for real progress, veteran handymen recommend vinegar on a stove top.

1. Once a year
   Every two years
2. Every five years
   Every 10 years

Fortunately, the septic tank doesn't need attention that often. Liquid, non-toxic "graywater" is allowed to leach out, steadily making room for waste that doesn't break down as readily.